Minka Lavery 4959-267B Bedienerhandbuch PDF herunterladen

INSTALLATION INSTRUCTION FOR 4959

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

READ AND SAVE THESE INSTRUCTIONS

ASSEMBLING THE FIXTURE (Fig. 2)

1. Shut off the power at the circuit breaker and remove the old

fixture, including the mounting hardware.

2. Carefully remove the fixture from the carton and check that

all parts are included as shown in the illustration.

3. Thread the center pipe (O) onto the nipple (P) and the

nipple (N) into the center pipe (O).

4. Place the coupling (M) and the tube (L) over the nipple (N),

then secure with the loop (K).

5. Secure the top of the arms (R) to the coupling (M) with the

screws (Q).

6. Secure the lower end of the arms (R) to the fixture arm (T)

with the screws (S).

HANGING THE FIXTURE (Fig. 1)

7. Thread the nipple (E) into the ceiling loop (G) until snug.

8. Thread the hex nut (D) onto the nipple (E). Place the lock

washer (C) over end of the nipple (E).

9. Thread other end of the nipple (E) with the loop into the

crossbar (A) until snug.

10. Take this crossbar (A) assembly and mount to ceiling

junction box with the mounting screws (B) (Size: #8-

32*0.6”L). The side of the mounting bar marked “GND”

must face out.

11. Connect quick link (J) to end of chain (I), then connect

quick link (J) to fixture loop (K).

12. By measuring, determine connect number of links needed

for desired hanging height.

13. Lace the fixture wires through the chain links, slip screw

collar ring (G) and canopy (F) over the chain.

14. Open one link of the other end of the chain (I) and connect

it to the ceiling loop (G).

15. Feed the fixture wires through the ceiling loop (G) and the

nipple (E) and pull until taut.

CONNECTING THE WIRES (Fig. 3)

16. At this point, connect the electrical wires as shown in Fig. 3

making sure all wire connectors are secured. If your outlet

box has a ground wire (green or bare copper) connect

fixture’s ground wire to it. Otherwise connect fixture’s

ground wire directly to the crossbar (A) using the green

screw provided. After the wires are connected, tuck them

neatly inside the junction box

17. Raise the canopy (F) all the way to the ceiling.

18. Raise the screw collar ring (H) and thread onto ceiling loop

(G) protruding through canopy (F). (Fig.1)

19. Place the glass shade (V) and cup (W) over the socket (U)

and secure with the socket ring (X) by wrench (Y).

20. Install the light bulbs in accordance to the fixture’s

specifications (DO NOT EXCEED THE SPECIFIED

WATTAGE!) (NE PAS DEPASSER LA PUISSANCE

NOMINALE MAXIMALE!)

Your installation is now complete. Return the power to the

junction box and test the fixture.

Fig.2

Fig.1

Set#

Crossbar

Ground screw

Mounting screw*2

A 016

Chain# HCH2072-267B

(3.8mm)

X: SKT-RING-26

Y: WRH-T1-51

X: SKT-RING-26 1
Y: WRH-T1-51 1

Inhaltsverzeichnis

Seite 1 - Y: WRH-T1-51

INSTALLATION INSTRUCTION FOR 4959WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES O

Kommentare zu diesen Handbüchern

Keine Kommentare

Minka Lavery 4959-267B Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Nein Minka Lavery 4959-267B herunter. Minka Lavery 4959-267B Instructions / Assembly Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Minka Lavery 4959-267B