Minka Lavery 2933-84-L Bedienerhandbuch PDF herunterladen

Fig.2

INSTALLATION INSTRUCTIONS

FOR 2933-L

For LED Wall Mount Fixture

WAR N I NG ! S H UT P OW E R O F F AT F US E O R CI RC U I T B R E AK E R .

AV E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R .

Fig.1F

Fig.3

IMPORTANT: Fixture should be installed by a

qualified electrician to ensure proper wiring and

installation.

Dimmable with C-L (CFL & LED) type and

Incandescent/Halogen type dimmers

II 798

PREPARATION

1. Shut off power at the fuse box or circuit breaker box. If

necessary remove the existing fixture and its mounting

hardware from the wall.

2. Carefully remove the new fixture from the carton and check

that all parts are included as shown in the illustration.

3. Position mounting plate (A) on the wall, and mark the

location of the two drywall anchors (G). Pre-drill the holes for

the drywall anchors (G). Then insert the drywall anchors (G)

into the wall.

HANGING THE FIXTURE (Fig.1)

4. Attach the mounting plate (A) to the outlet box using outlet

box screws (B) (Size: 8-32*1/2’’L). The side of the mounting

plate marked “GND” must face out.

5. Place the wood screws (F) through the holes of the

mounting plate (A) and into the drywall anchors (G) to

secure the mounting plate (A) to the wall.

CONNECTION THE WIRES (Fig. 2)

6. At this point, connect the electrical wires as shown in Fig.2,

making sure that all wire connectors are secured. If your

outlet box has a ground wire (green or bare copper), connect

the fixture's ground wire to it. Otherwise, connect the

fixture's ground wire directly to the mounting plate using the

green screw provided. After the wires are connected, tuck

them carefully into the outlet box.

FINISHING THE INSTALLATION (Fig. 1)

7. Align Fixture (E) over mounting plate (A) and secure with

screws (D).

Your installation is now complete. Return power to the outlet box

and test the fixture.

CAUTION /ATTENTION: When handling the fixture, do not

apply pressure to the LEDs. Hold the fixture by the base or

fixture body (E) only.

Replacing LED module (Fig.3)

The LED module can be replaced by a qualified electrician without

cutting the wires and without damaging the decorative element to

which the fixture is attached. See installation steps for more details

(Fig 3.)

Warning: Turn off power at the fuse box or circuit breaker

before replacing LED module.

a. To remove the fixture from the wall: loosen screws (D), and

remove the wire connectors. Then place the fixture on a clear

flat surface.

b. Loosen screws (P), hex nuts (F) screws (M), wire fastener (N)

and then carefully remove LED module (I).

c. Reverse steps a-b for installing the new LED module.

Note: The LED module should be provided by a specified supplier.

Inhaltsverzeichnis

Seite 1 - FOR 2933-L

Fig.2INSTALLATION INSTRUCTIONSFOR 2933-LFor LED Wall Mount FixtureWAR N I NG ! S H UT P OW E R O F F AT F US E O R CI RC U I T B R E AK E R

Kommentare zu diesen Handbüchern

Keine Kommentare

Minka Lavery 2933-84-L Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Nein Minka Lavery 2933-84-L herunter. Minka Lavery 2933-84-L Instructions / Assembly Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Minka Lavery 2933-84-L