Minka Lavery 4935-284 Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Nein Minka Lavery 4935-284 herunter. Minka Lavery 4935-284 Instructions / Assembly Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 1
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
INSTALLATION INSTRUCTIONS FOR FIXTURE #4935
ASSEMBLING THE FIXTURE (FIG. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the mounting
hardware.
2. Carefully remove the new fixture from the carton and check that
all parts are included as shown in the illustration.
3. Thread the fixture loop (A) tightly onto the nipple (B).
4. Adjust the fixture arms to their proper position.
5. Put the glass shade (E) over the socket (F), then secure with the
cushion ring (D) and socket ring (C).
6. Install the light bulb in accordance with fixture’s specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!) (NE
PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
MOUNTING THE FIXTURE (FIG. 2)
1. Thread the nipple (S) tightly into the collar loop (T).
2. Thread the other end of nipple (S) into the cross bar (P).
The side of the cross bar marked with “GND” must face out.
3. Place lock washer (Q) over the end of nipple (S) protruding
through cross bar (P) and thread hex nut (R) onto nipple (S) until
tight.
4. Take this crossbar assembly and mount to ceiling outlet box (V)
tightly using outlet box screws (W).
5. Use proper chain pliers to open one end link of the chain and
connect to the fixture loop (A). Close the link.
6. By measuring, determine correct number of links needed for
proper hanging height. Using the chain pliers, disconnect and
discard remaining chain.
7. Carefully lace the fixture wires through the chain (X).
8. Slip collar ring (Y) over the chain (X), then do the same with
canopy (U).
9. Open the other end link of the chain (X) and connect to the collar
loop (T). Close the link.
10. Feed the fixture wires through the collar loop (T) and nipple (S)
and pull until tight.
CONNECTING THE WIRES
1. At this point, connect the electrical wire as shown in the wiring
diagram, making sure that all wire connectors are secured. If
your outlet has a ground wire (green or bare copper), connect
the fixtures ground wire to it. Otherwise, connect the fixture
ground wire directly to the crossbar using the Green Screw
provided.
2. Tuck these wires connectors neatly into the ceiling outlet box
and raise the collar ring (Y) and thread onto collar loop (T)
protruding through the canopy.
Your installation is now complete. Return power to the junction box
and test the fixture.
Notice: It is important to use proper chain pliers (not
included) to OPEN and CLOSE the chain included with
this fixture. Do not open them with other tools that may
twist or stress the chain links. It is important to use
proper chain pliers like the ones shown in the diagram.
GLASS SHADE(E)
SOCKET(F)
LOOP(A)
NIPPLE(B)
FIXTURE
BODY
Fig. 1
Fig. 2
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
(SKT-RING-26)
Chain # HCH3072-281
Gauge 4.5MM
Seitenansicht 0
1

Inhaltsverzeichnis

Seite 1

INSTALLATION INSTRUCTIONS FOR FIXTURE #4935ASSEMBLING THE FIXTURE (FIG. 1)1. Shut off the power at the fuse box or circuit breaker. Ifnecessary, remov

Kommentare zu diesen Handbüchern

Keine Kommentare