Minka Lavery 3137-648 Bedienerhandbuch PDF herunterladen

INSTALLATION INSTRUCTIONS FOR FIXTURE #3137-648

ASSEMBLING THE FIXTURE (FIG. 1)

1. Shut off the power at the fuse box or circuit breaker. If

necessary, remove the old fixture including the mounting

hardware.

2. Carefully remove the new fixture from the carton and check that

all parts are included as shown in the illustration.

3. Thread the fixture loop (A) onto the nipple (B) until snug.

4. Place the tubes (E) over the sockets (F).

5. Install the light bulbs (not included) in accordance with the

fixture’s specifications. (DO NOT EXCEED THE MAXIMUM

WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE

NOMINALE MAXIMALE!).

6. Hang the crystal drops (C and H) onto the small rings (D) as

shown in Fig. 2.

7. Hang the crystal chains (G and I) onto the fixture as shown in

Figure 2.

MOUNTING THE FIXTURE (FIG. 2)

1. Thread the nipple (S) into the collar loop (T) until snug.

2. Thread the other end of nipple (S) into the cross bar (P).

3. Place lock washer (Q) and hex nut (R) over the end of nipple (S)

protruding through cross bar (P), then thread hex nut (R) to nipple

(S) until snug.

4. Take this crossbar assembly and mount to ceiling outlet box (V)

using outlet box screw (W). The side of cross bar marked

“GND” must face out.

5. Use proper chain pliers to open one end link of the chain and

connect to the fixture loop (A). Then close the link.

6. By measuring, determine the correct number of links needed for

The desired hanging height. Using the chain pliers, disconnect

and discard the remaining chain.

7. Carefully lace the fixture wires through the chain (X).

8. Slip the lock collar (Y) and canopy (U) over the chain (X), allowing

them to rest on the fixture loop (A).

9. Open the other end link of the chain (X) and connect to the collar

loop (T). Then close the link.

10. Feed the fixture wires through the collar loop (T) and nipple (S)

and pull until tight.

CONNECTING THE WIRES (See Wiring Diagram)

1. Connect the electrical wire as shown in the wiring diagram,

making sure that all wire connectors are secured. If your outlet

box has a ground wire (green or bare copper), connect the

fixture’s ground wire to it. Otherwise, connect the fixture’s

ground wire directly to the mounting plate using the green screw

provided.

2. Tuck the wire connectors neatly into the ceiling outlet box

and raise the canopy (U) to the ceiling. Then raise lock collar

(Y) and thread onto collar loop (T) protruding through canopy

(U).

Your installation is now complete. Return power to the outlet box

and test the fixture.

Notice: It is important to use proper chain pliers (not

included) to OPEN and CLOSE the chain included with

this fixture. Do not open them with other tools that may

twist or stress the chain links. It is important to use

proper chain pliers like the ones shown in the diagram.

CRYSTAL DROP(C)

SMALL RING(D)

TUBE(E)

SOCKET(F)

CRYSTAL DROP(H)

CRYSTAL CHAIN(G)

CRYSTAL CHAIN(I)

CRYSTAL DROP(C)

SMALL RING(D)

Fig. 1

Fig. 2

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Set A#A-010

-Crossbar

-Ground Screw

-Mounting screws (2)

Chain # HCH3072-648

Gauge 4.50MM

Inhaltsverzeichnis

Seite 1

INSTALLATION INSTRUCTIONS FOR FIXTURE #3137-648ASSEMBLING THE FIXTURE (FIG. 1)1. Shut off the power at the fuse box or circuit breaker. Ifnecessary, r

Kommentare zu diesen Handbüchern

Keine Kommentare

Minka Lavery 3137-648 Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Nein Minka Lavery 3137-648 herunter. Minka Lavery 3137-648 Instructions / Assembly Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Minka Lavery 3137-648